Support Forums/Technical Support Forums/OMC Outdrives

 

ask a question

Most asked | Recent | Needs answer (38) | Answered

Answered
4

Replace tilt drive motor for 1982 omc 400 outdrive attached to 2.5 engine

Carl W Bosin October 14, 2010

Answered
2

What is the purpose of the two fuel pumps on OMC 5.0

Terry Fredrick June 05, 2010 • Latest comment • 1

Answered
1

2.3 L OMC Stern drive distributor

Dustin Will July 23, 2010 • Latest comment • 4

Answered

omc stringer no reverse?

Brian Mc Nally August 23, 2010 • Latest comment • 5

Answered

Cobra Shift adjustment

Chuck Hoffman August 31, 2010 • Latest comment • 2

Answered

Need clues on engine running hot

Paul Vines July 07, 2010 • Latest comment • 2

Answered

Temperature sensor?

George Rice July 03, 2010 • Latest comment • 2

Answered

OMC Stringer Shift Cap and Cable Installation help!!!! Mayday

dave pope July 13, 2010 • Latest comment • 2

Answered

boat want throttle up in water

Collin Peters June 16, 2010 • Latest comment • 2

Answered

OMC 400 mech shift sounds like it's missing

Chris Browne December 13, 2011 • Latest comment • 1

Answered

Manufacturing date of a 150HP Johnson Outboard Engine

Shmuelw August 28, 2010 • Latest comment • 1

Answered

rinker lover 1989/350 going back dist with point set had too many volts

Danitatexoma July 07, 2010 • Latest comment • 1

Answered

Outdrive gear lubrication

John Kavanagh September 07, 2010 • Latest comment • 1

Answered

omc outdrive shift cable

Mshawme September 16, 2010 • Latest comment • 1

Answered

Replacing Mallory points dist. with early HEI GM

Luckypennyranch September 14, 2010 • Latest comment • 1

Answered

LOWER UNIT SHIFT CABLES

Thof54 August 26, 2010 • Latest comment • 1

Answered

Outdrive tilts up in reverse

Alvin Quint August 16, 2010 • Latest comment • 1

Answered

omc outdrive shift promblems

Plpstg02 August 17, 2010 • Latest comment • 1

Answered

i/o sputtering

Jenash3 August 17, 2010 • Latest comment • 1

Answered

leaking water in engine compartment while in gear

Matthew Schneider July 20, 2010 • Latest comment • 1

Answered

what parts are involved in starter turning over and disengaging when started

Don Coyne August 02, 2010 • Latest comment • 1

Answered

OMC trim motor

Daveprodoor July 08, 2010 • Latest comment • 1

Answered

Stringer - 1985 Engine runs & outdrive shifts, no through power

Dan2 July 16, 2010 • Latest comment • 1

Answered

OMC Cobra 3.0 shift cable

Warren Greg July 10, 2010 • Latest comment • 1

Answered

OMC Stern drive

Wellmann July 19, 2010 • Latest comment • 1

Answered

1987 OMC 4.3 litre V6

Joe Foster February 17, 2010 • Latest comment • 1

Answered

Trick to aligning motor install through gimbal bearing with alignment tool.

Mark E. Kunnemann Feb 22

Answered

I have a 1986 Omc 800 outdrive 5,7 ,

curt wikel Feb 21

Answered

1989 omc sterndrive v8 5.7 cobra

Wally Tillmanns September 19, 2010

Answered

OMC 460 7.5L Impeller shaft

Scott Slagh September 16, 2011